This site uses cookies. By continuing to browse the ConceptDraw site you are agreeing to our Use of Site Cookies.

Design elements - Pipes (part 1)

The vector stencils libraries "Pipes 1" and "Pipes 2" contain 28 and 48 pipe, tubing and fitting symbols, respectively.
"A fitting is used in pipe plumbing systems to connect straight pipe or tubing sections, to adapt to different sizes or shapes, and for other purposes, such as regulating or measuring fluid flow. The term plumbing is generally used to describe conveyance of water, gas, or liquid waste in ordinary domestic or commercial environments, whereas piping is often used to describe high-performance (e.g. high pressure, high flow, high temperature, hazardous materials) conveyance of fluids in specialized applications. The term tubing is sometimes used for lighter-weight piping, especially types that are flexible enough to be supplied in coiled form.
Fittings (especially uncommon types) require money, time, materials, and tools to install, so they are a non-trivial part of piping and plumbing systems." [Piping and plumbing fitting. Wikipedia]
Use the design elements libraries "Pipes 1" and "Pipes 2" for drawing plumbing and piping building plans, schematic diagrams, blueprints, or technical drawings of waste water disposal systems, hot and cold water supply systems using the ConceptDraw PRO diagramming and vector drawing software.
The shapes libraries "Pipes 1" and "Pipes 2" are contained in the Plumbing and Piping Plans solution from the Building Plans area of ConceptDraw Solution Park. Read more
Piping symbols
Piping symbols, tundish, syphon drain, swivel joint, strainer, soldered, solvent, socket, spigot, socket weld, sleeve joint, separator, screwed joint, open vent, liquid seal, joint, hydrant, flanged, bolted, flame arrester, exhaust silencer, exhaust head, end cap, electrically insulated, electrically bonded, drain silencer, butt weld, bursting disc, bell mouth, Y strainer,
This engineering drawing present weld type symbols and fillet weld symbols.
The weld type symbol is typically placed above or below the center of the reference line, depending on which side of the joint it's on. The symbol is interpreted as a simplified cross-section of the weld.
"Fillet welding refers to the process of joining two pieces of metal together whether they be perpendicular or at an angle. These welds are commonly referred to as Tee joints which are two pieces of metal perpendicular to each other or Lap joints which are two pieces of metal that overlap and are welded at the edges. The weld is aesthetically triangular in shape and may have a concave, flat or convex surface depending on the welder’s technique. Welders use fillet welds when connecting flanges to pipes, welding cross sections of infrastructure, and when fastening metal by bolts isn't strong enough." [Fillet weld. Wikipedia]
The engineering drawing example Welding symbols is included in the Mechanical Engineering solution from Engineering area of ConceptDraw Solution Park. Read more
Welding joint symbols
Welding joint symbols, square groove, insert, consumable insert, flare bevel groove, flared-bevel groove, flare V groove, flared-V groove, fillet, weld, cutaway, revealing detail, bevel groove, back, backing, arrow, V-groove, U-groove, J-groove,
The vector stencils library "Pipes 2" contains 48 symbols of pipes. Use it for drawing plumbing and piping building plans, schematic diagrams, blueprints, or technical drawings of waste water disposal systems, hot and cold water supply systems in the ConceptDraw PRO diagramming and vector drawing software extended with the Plumbing and Piping Plans solution from the Building Plans area of ConceptDraw Solution Park. Read more
Crossing
Crossing, crossing,
Junction
Junction, junction,
Basic support
Basic support, basic support,
Guide 1
Guide 1, guide,
Guide 2
Guide 2, guide,
Guide 3
Guide 3, guide,
Stopper
Stopper, stopper,
Anchor
Anchor, anchor,
Support / anchor
Support / anchor, support, anchor,
Hunger
Hunger, hunger,
Cross
Cross, cross,
Double branch
Double branch, double branch,
Jacketed
Jacketed, jacketed,
Sleeved
Sleeved, sleeved,
Sleeve joint
Sleeve joint, sleeved, sleeve joint,
Expansion sleeve joint
Expansion sleeve joint, sleeved, expansion sleeve joint,
Lagged
Lagged, lagged,
Bellows
Bellows, bellows,
Flow indication
Flow indication, flow indication,
Flow indication 2
Flow indication 2, flow indication,
Reducer
Reducer, reducer,
Reducer,arrow
Reducer,arrow, reducer,
Pipe bore change
Pipe bore change, pipe bore change,
Flexibility provision
Flexibility provision, flexibility provision,
Sleeve extension
Sleeve extension, sleeve extension,
Flow restrictor
Flow restrictor, flow restrictor,
Elbow 45
Elbow 45, elbow,
Elbow 90
Elbow 90, elbow,
Heated or cooled
Heated or cooled, heated, cooled,
Pneumatic line
Pneumatic line, pneumatic line,
Signal line
Signal line, signal line,
Electric line
Electric line, electric line,
Hydraulic line
Hydraulic line, hydraulic line,
Capillary line
Capillary line, capillary line,
Internal connection
Internal connection, internal connection,
Route radiation
Route radiation, route radiation,
Mechanical linkage
Mechanical linkage, mechanical linkage,
Electrical device
Electrical device, electrical device,
Vibratory device
Vibratory device, vibratory device,
Weight device
Weight device, weight device,
Spray device
Spray device, spray device,
Rotary motion
Rotary motion, rotary motion,
Stirring / fan
Stirring / fan, stirring, fan,
Access points
Access points, access points,
Trap
Trap, trap,
Expansion loop
Expansion loop, expansion loop,
Flexible hose
Flexible hose, flexible hose,
Flexible hose, flanged
Flexible hose, flanged, flexible hose,
The vector stencils libraries "Pipes 1" and "Pipes 2" contain 28 and 48 pipe, tubing and fitting symbols, respectively.
"Pipe is hollow cylinder used to conduct or transfer fluids (liquids and gases) from one place to other place. The main difference between pipe and tube is the critical dimension used to describe the pipe size or the tube size. For pipe, internal diameter (ID) roughly corresponds to the nominal pipe size for standard wall thickness. For tube, the outer diameter (OD) closely corresponds to the tube size. In current European standards pipes and tubes are nowadays described as outside diameter by wall thickness. The three standard types of pipe ends used in the piping industriesare; Plain Ends (PE), Threaded Ends (TE) and Beveled Ends (BE). In the past, many types of material have been used in conveying water from one point to another. Masonry and wood were probably the first materials used. Plastics are the newest, and are now being used quite extensively." [Piping. Wikipedia]
Use the design elements libraries "Pipes 1" and "Pipes 2" for drawing plumbing and piping building plans, schematic diagrams, blueprints, or technical drawings of waste water disposal systems, hot and cold water supply systems using the ConceptDraw PRO diagramming and vector drawing software.
The shapes libraries "Pipes 1" and "Pipes 2" are contained in the Plumbing and Piping Plans solution from the Building Plans area of ConceptDraw Solution Park. Read more
Piping symbols
Piping symbols, weight device, vibratory device, trap, support, anchor, stopper, stirring, fan, spray device, sleeved, sleeve joint, sleeved, expansion sleeve joint, sleeved, sleeve extension, signal line, route radiation, rotary motion, reducer, pneumatic line, pipe bore change, mechanical linkage, lagged, junction, jacketed, internal connection, hydraulic line, hunger, heated, cooled, guide, flow restrictor, flow indication, flexible hose, flexibility provision, expansion loop, electrical device, electric line, elbow, double branch, crossing, cross, capillary line, bellows, basic support, anchor, access points,
The vector stencils library "Valves and fittings" contains 104 symbols of valve components.
Use these icons for drawing industrial piping systems; process, vacuum, and fluids piping; hydraulics piping; air and gas piping; materials distribution; and liquid transfer systems.
"A valve is a device that regulates, directs or controls the flow of a fluid (gases, liquids, fluidized solids, or slurries) by opening, closing, or partially obstructing various passageways. Valves are technically valves fittings, but are usually discussed as a separate category. In an open valve, fluid flows in a direction from higher pressure to lower pressure.
The simplest, and very ancient, valve is simply a freely hinged flap which drops to obstruct fluid (gas or liquid) flow in one direction, but is pushed open by flow in the opposite direction. This is called a check valve, as it prevents or "checks" the flow in one direction. ...
Valves are found in virtually every industrial process, including water & sewage processing, mining, power generation, processing of oil, gas & petroleum, food manufacturing, chemical & plastic manufacturing and many other fields. ...
Valves may be operated manually, either by a handle, lever, pedal or wheel. Valves may also be automatic, driven by changes in pressure, temperature, or flow. These changes may act upon a diaphragm or a piston which in turn activates the valve, examples of this type of valve found commonly are safety valves fitted to hot water systems or boilers.
More complex control systems using valves requiring automatic control based on an external input (i.e., regulating flow through a pipe to a changing set point) require an actuator. An actuator will stroke the valve depending on its input and set-up, allowing the valve to be positioned accurately, and allowing control over a variety of requirements." [Valve. Wikipedia]
The example "Design elements - Valves and fittings" was created using the ConceptDraw PRO diagramming and vector drawing software extended with the Chemical and Process Engineering solution from the Engineering area of ConceptDraw Solution Park. Read more
Valves and fittings symbols
Valves and fittings symbols, wedge gate valve, valve manifold, tundish, swivel joint, strainer, stop check valve, soldered, solvent, socket, spigot, socket,  spigot, socket weld, sleeve joint, separator, screwed sleeve, screwed joint, screw-down valve, screw-down check valve, relief valve, relief angle valve vacuum, relief angle valve pressure, reel valve, reducing valve, reducer, powered valve, plug valve straight through, plug valve T point, plug valve L point, plug valve 3 way, plug valve, parallel slide valve, open vent, needle valve, lock-shield valve, liquid seal, joint, hydrant, globe valve, gate valve, float operated valve, flanged valve, flanged joint, bolted joint, flame arrester, exhaust silencer, exhaust head, end cap socket and spigot, end cap screwed, end cap quick release, end cap flanged and bolted, end cap fillet welded, end cap butt welded, end cap	screwed and plugged, end cap, electrically insulated, electrically bonded, drain silencer, diaphragm valve, check valve, characterized port valve, butterfly valve, butt weld, bursting disc, bell mouth, ball valve, angle valve, Y strainer, 3-way plug valve,