This site uses cookies. By continuing to browse the ConceptDraw site you are agreeing to our Use of Site Cookies.

mechanical engineering, mechanical design software, mechanical drawing symbols, mechanical drawing software Mechanical Engineering

mechanical engineering, mechanical design software, mechanical drawing symbols, mechanical drawing software
This solution extends ConceptDraw PRO v.9 mechanical drawing software (or later) with samples of mechanical drawing symbols, templates and libraries of design elements, for help when drafting mechanical engineering drawings, or parts, assembly, pneumatic,
The vector stencils library "Pipes 2" contains 48 symbols of pipes. Use it for drawing plumbing and piping building plans, schematic diagrams, blueprints, or technical drawings of waste water disposal systems, hot and cold water supply systems in the ConceptDraw PRO diagramming and vector drawing software extended with the Plumbing and Piping Plans solution from the Building Plans area of ConceptDraw Solution Park.
Crossing, crossing,
Junction, junction,
Basic support
Basic support, basic support,
Guide 1
Guide 1, guide,
Guide 2
Guide 2, guide,
Guide 3
Guide 3, guide,
Stopper, stopper,
Anchor, anchor,
Support / anchor
Support / anchor, support, anchor,
Hunger, hunger,
Cross, cross,
Double branch
Double branch, double branch,
Jacketed, jacketed,
Sleeved, sleeved,
Sleeve joint
Sleeve joint, sleeved, sleeve joint,
Expansion sleeve joint
Expansion sleeve joint, sleeved, expansion sleeve joint,
Lagged, lagged,
Bellows, bellows,
Flow indication
Flow indication, flow indication,
Flow indication 2
Flow indication 2, flow indication,
Reducer, reducer,
Reducer,arrow, reducer,
Pipe bore change
Pipe bore change, pipe bore change,
Flexibility provision
Flexibility provision, flexibility provision,
Sleeve extension
Sleeve extension, sleeve extension,
Flow restrictor
Flow restrictor, flow restrictor,
Elbow 45
Elbow 45, elbow,
Elbow 90
Elbow 90, elbow,
Heated or cooled
Heated or cooled, heated, cooled,
Pneumatic line
Pneumatic line, pneumatic line,
Signal line
Signal line, signal line,
Electric line
Electric line, electric line,
Hydraulic line
Hydraulic line, hydraulic line,
Capillary line
Capillary line, capillary line,
Internal connection
Internal connection, internal connection,
Route radiation
Route radiation, route radiation,
Mechanical linkage
Mechanical linkage, mechanical linkage,
Electrical device
Electrical device, electrical device,
Vibratory device
Vibratory device, vibratory device,
Weight device
Weight device, weight device,
Spray device
Spray device, spray device,
Rotary motion
Rotary motion, rotary motion,
Stirring / fan
Stirring / fan, stirring, fan,
Access points
Access points, access points,
Trap, trap,
Expansion loop
Expansion loop, expansion loop,
Flexible hose
Flexible hose, flexible hose,
Flexible hose, flanged
Flexible hose, flanged, flexible hose,
This example engineering drawing showing the hydraulic directional control valve usage with floating motor and pressure compensated pump is redesigned using the ConceptDraw PRO diagramming and vector drawing software from the Wikimedia Commons file: DCV 17.jpg.
[ wiki/ File:DCV_ 17.jpg]
This file is licensed under the Creative Commons Attribution-Share Alike 3.0 Unported license.
[ licenses/ by-sa/ 3.0/ deed.en]
"Directional control valves are one of the most fundamental parts in hydraulic machinery as well and pneumatic machinery. They allow fluid flow into different paths from one or more sources. They usually consist of a spool inside a cylinder which is mechanically or electrically controlled. The movement of the spool restricts or permits the flow, thus it controls the fluid flow. ...
The spool (sliding type) consists of lands and grooves.The lands block oil flow through the valve body. The grooves allow oil or gas to flow around the spool and through the valve body. There are two fundamental positions of directional control valve namely normal position where valve returns on removal of actuating force and other is working position which is position of a valve when actuating force is applied. There is another class of valves with 3 or more position that can be spring centered with 2 working position and a normal position. ...
Directional control valves can be classified according to:
(1) number of ports;
(2) number of positions;
(3) actuating methods;
(4) type of spool." [Directional control valve. Wikipedia]
The fluid power equipment drawing example "Directional control valve" is included in the Mechanical Engineering solution from the Engineering area of ConceptDraw Solution Park.
Hydraulic equipment schematic
Hydraulic equipment schematic, spring, variable spring, non-variable spring, reservoir, pressure compensator, hydraulic pump, four-port, flow path, four-port, crossed, flow path, flow path, floating motor, filter, electric linear, solenoid, dot, line, junction, closed path, closed port, callout, box, flow path,